Simulink Tester Issues

From T-VEC Wiki
Revision as of 14:40, 25 February 2007 by Admin (Talk | contribs)

Jump to: navigation, search

This section describes potential limitations, issues and associated guidance for using T-VEC with Simulink and Stateflow.



Test Vector Generation Failures

If test vector failures occur

  1. Check to make sure that the lower-level subsystems do not have failures, correct those failures first
  2. Check to make sure that the constraints of lower-level subsystem do not preclude satisfiability associated with higher-level subsystems that reference the lower-level subsystems
  3. Use the Auto Rotate Convergence Fix Mode in the Vector Generator Properties of VGS
  4. Ensure the range settings of inputs variables do not preclude satisfiability


Simulation Test Drivers: State Data Initialization

T-VEC produces test vectors that may contain state data for feedback constructs such as the unit delay. This results in state data, but there is currently no control mechanisms in the Matlab simulator to set (initialize) state data.


Inlining and Coverage

Use of inlining Simulink subsystems can impact test and model coverage. If a model includes inlined subsystems, then the missing coverage may be related to situations where the model doesn't support taking one of the paths through the utilities (lower-level subsystem) based simply on the model's design.

It is the very nature of design models vs requirements models. Designs include re-usable/generic components whose logic won't necessarily be needed for all applications.

Here's an example: Subsystem X is a utility that has an input A with two paths:

A >= 0 then do something
A < 0 then do something

Subsystem Y inlines subsystem X, but has references to Subsystem X only when the input associated with the signal A is >= 0. This means that there cannot be model or test coverage for the path when A < 0.

The only solution is to make sure they are treated as stand-alone atomic functions so that they may be tested in their own right.

Test Vector Generation Failures

T-VEC VGS analysis is exhaustive in the sense that for every DCP throughout the hierarchy of systems it is model-checked, and a test vector is them produced. Most test vector generation failures results from model defects where the constraints of the DCP are not satisfiable throughout the hierarchy of DCPs of the subsystems.

However, there are possible situations where test vector generation fails when it is possible to find vectors, for example when signal domains are left to their defaults. There are default settings for ranges values, but these may not be adequate for the application.

T-VEC does cover a large percentage of every model use standard block, however, dynamic array indexing, and cases of spacial discontinuity coupled with circular dependent variable relationships that cause forward convergence to move into the "left hand" (output) disconnected space and backward propagation to move into "right hand" (input) disconnected space and no solution is possible with existing mechanisms. This is rather rare, but it does happen. The T-VEC test generation algorithms continue to evolve to deal with classes of these kind of situations, but there is no guarantee that there will never be a problem. For such situation contact for additional assistance.

The auto-rotate is one of the mechanisms that address this issue, most are applied automatically, independent of the specific convergence mode. Finding test vectors, by hand, for these cases is likely to be equally problematic.

Signal Range Management

Changes in architectural decomposition may cause a signal name to be removed. For example, if a signal is defined as signal A in scope subsystems x\y\z and subsystem y is removed, then that signal is undefined and is removed from the signal range file (with extension .srf).

The translator creates a backup copy of the signal range file (.srf) each time the translator is run. It creates a log file that details every change to the .srf file. It should be possible to recover from an unexpected change to the .srf file.

Model Coverage vs. Code Coverage

Test vector generation attempts to find test vectors for all of the paths (DCPs) in the model. Complete coverage means complete model coverage, however, complete model coverage does not guarantee coverage of code (e.g., MCDC coverage), for example: code generators can put in code (e.g., safety code around square root function). The Simulink Testers provides mechanisms such as assertions and coverage predicates that can be used to produce additional tests to cover many possible situations. Tools such as LDRA TBrun is integrated with the Simulink Tester and can provide test coverage measures to support organization that may need evidence to support FAA certification.

Test Sequence Vectors: State Variable Initialization

Test Sequence Vectors are created by referencing the target subsystem multiple times. Special T-VEC subsystems are created based on a configuration file supplied to the translator. These TSV subsystems include one or more test sequences. Each test sequence includes one or more references to the target subsystem (i.e., the number of sample times being tested). It also includes a set of the target subsystem’s inputs for each time that the target subsystem is referenced. These input values have their respective subsystem reference appended to their name. Therefore, if a subsystem has two inputs, inputA and inputB, then a TSV subsystem that includes two references would include the inputs inputA_1, inputB_1, inputA_2 and inputB_2. Input values to each subsystem reference can be controlled through settings at the reference level, test sequence level or subsystem level.

Many blocks in Simulink have specific initial condition values, unit delays, integrators, etc. (and stateflow in terms of things like initial states of state machines). T-VEC has a mechanism for using these initial values during vector generation. T=0 defines a point in time where all test vectors are generated as if the system is in the first cycle of execution. When option is T>=0 TSVs are generated for things that take place after the first cycle and then continue for multiple cycles of the TSV. When T>0 it turns off the initial condition setting action and allow the state variables to be solved for through convergence rather than be initilized/assigned.

VGS Property: State Variable Inits

The default is to generate vectors for both cases, 2 vectors per DCP when no state variables are available, but T-VEC produces 4 vectors when state variables are available.

Test Driver Generation

There are some situation where manual support is needed for test driver generation in both Simulink and Stateflow models where some inputs not available from RTW. There are cases where it is simply not possible to predict variable names, function parameter orders, etc. There is no API for determining the choices made by the RTW to fully automate all aspects of test driver map file creation.

There is a work around with the current schemas - all mapping descriptors are passed through a Perl function before going into the target file. The perl script parses in an external file that contains new replacement mapping information. The mapping can be either by the descriptor itself or the mapping key. If the perl script finds a match then it uses the replacement from the file. This function can be extended directly through the Perl script.